Item Code: 26011200

Blue Sea M series battery switch. DUAL CIRCUIT PLUS Black

£42.00
(Ex £35.00)
 
Order in the next Hours Mins and Seconds,
To get your item delivered on Tuesday

Dual Circuit Plus
Simultaneously switches two isolated battery banks or combines battery banks to all loads. CAN NOT be used to switch positive and negative conductors because of the combine feature.

8-26011200

M Series battery switches: 300 Ampere continuous rating for outboards and small gasoline or diesel engines.
Available in Red or Black.  Black subject to order, not normally held in stock.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 38" (M10) ring terminals
One-piece terminal stud design never loosens over time
78" (22.22mm) stud length accepts multiple cable terminals
Isolating cover with three snap-in side pieces protects rear contacts and allows wire access in any direction
Case design allows surface, rear, or front panel mounting options
Label with international legends 6 ICON label set included for circuit identification*
* 6005 includes illustrated ONOFF label only
All battery switches feature removable knob which remains positively retained and tactile indicator conveys position by feel, except for 6005 which has a positively retained removable key.
Make-before-break contact design allows switching between battery banks without power interruption.

Dual Circuit Plus Explained
The Dual Circuit Plus is recommended when:
Ease of use is desired
Battery bank selection is not necessary
Using sensitive electronics
Paired with an Automatic Charging Relay (ACR)
The Dual Circuit Plus is a double pole switch designed to supply power to the devices that are connected to a specific battery bank.  This means house electronics are isolated from the engine bank.
This both preserves the starting battery and prevents sensitive electronics from being subjected to voltage sags and spikes during starting. Designed to be coupled with an Automatic Charging Relay (ACR) to provide simultaneous charging of two battery banks from the engines alternator. Below is a recommendation on how to properly use the Dual Circuit Plus Battery Switch when paired with an ACR.
1. Power is Needed - Turn the switch into the ON position.
2. No Power Needed (Storage) Select OFF to prevent current draw.
3. Emergency Parallel (Jump Starting) Turn the switch to the
Combine Batteries position designated in yellow. Once the engine is running, turn the switch to the ON position.

WARNING The positive and negative conductors should not be attached to the same battery switch.
The only exceptions are the Dual Circuit Battery Switches 6010 and 5510 Since these models have electrically isolated circuits and do not include a combine feature, they can provide disconnect to the positive and negative conductors simultaneously.

Dual Circuit Plus
Simultaneously switches two isolated battery banks or combines battery banks to all loads. CAN NOT be used to switch positive and negative conductors because of the combine feature.

8-26011200

M Series battery switches: 300 Ampere continuous rating for outboards and small gasoline or diesel engines.
Available in Red or Black.  Black subject to order, not normally held in stock.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 38" (M10) ring terminals
One-piece terminal stud design never loosens over time
78" (22.22mm) stud length accepts multiple cable terminals
Isolating cover with three snap-in side pieces protects rear contacts and allows wire access in any direction
Case design allows surface, rear, or front panel mounting options
Label with international legends 6 ICON label set included for circuit identification*
* 6005 includes illustrated ONOFF label only
All battery switches feature removable knob which remains positively retained and tactile indicator conveys position by feel, except for 6005 which has a positively retained removable key.
Make-before-break contact design allows switching between battery banks without power interruption.

Dual Circuit Plus Explained
The Dual Circuit Plus is recommended when:
Ease of use is desired
Battery bank selection is not necessary
Using sensitive electronics
Paired with an Automatic Charging Relay (ACR)
The Dual Circuit Plus is a double pole switch designed to supply power to the devices that are connected to a specific battery bank.  This means house electronics are isolated from the engine bank.
This both preserves the starting battery and prevents sensitive electronics from being subjected to voltage sags and spikes during starting. Designed to be coupled with an Automatic Charging Relay (ACR) to provide simultaneous charging of two battery banks from the engines alternator. Below is a recommendation on how to properly use the Dual Circuit Plus Battery Switch when paired with an ACR.
1. Power is Needed - Turn the switch into the ON position.
2. No Power Needed (Storage) Select OFF to prevent current draw.
3. Emergency Parallel (Jump Starting) Turn the switch to the
Combine Batteries position designated in yellow. Once the engine is running, turn the switch to the ON position.

WARNING The positive and negative conductors should not be attached to the same battery switch.
The only exceptions are the Dual Circuit Battery Switches 6010 and 5510 Since these models have electrically isolated circuits and do not include a combine feature, they can provide disconnect to the positive and negative conductors simultaneously.

Customer Reviews (0)